Pre-finished Engineered Timber

Finish: 12 Coats of PPG Water-based Polyurethane Lacquer

Installation: Direct Stick, Tongue & Groove joining system

Edge: Micro Bevelled

Engineered Timber Flooring is recommended for use in internal residential or commercial areas including, but not limited to, living areas, kitchens, bedrooms, hallways and stairs.

DO NOT INSTALL in bathrooms, laundries, toilets, saunas, or areas subject to regular moisture or water.

Storage:

Ensure the environment resembles installation conditions (20°C and 40-60% humidity) to avoid material damage.  Cartons should be placed in the installation area and remain unopened until commencement of installation.

Heated Subfloors

Most Engineered Timber Flooring can be installed over a heated slab using both installation methods – direct stick or floated. Most manufacturer's do not recommend installing Australian species timbers over underfloor heating. Please check with the manufacturer or supplier before installing.

The in-slab under floor heating needs to be started and run at desired temperature for at least 2 weeks prior to installation.

After 14 days, turn off slab heating and allow 4 days to pass in order to allow subfloor to cool down and reach room temperature before installation. Heating system temperature is to be increased by 2 degrees increments each day until desired temperature is reached (not exceeding 25 degrees Celsius) and when turning your heating off, also decrease by 2 degrees increments each day until it is off.

Subfloor Preparation

Ensure the subfloor is flat. For floating floors this generally does not exceed 3mm beneath a 1m long straight edge. For direct adhesive fix applications, 3mm beneath a 3m long straight edge applies.  For concrete subfloors a moisture barrier is required.

After Installation

Avoid placing rugs, mats, or very heavy furniture on the floor until it has fully acclimatised, which typically takes about 8 weeks. Additionally, direct sunlight should be minimised with window coverings to prevent heat-related damage.

25 Year Structural Warranty
Covered by a 25 Year Structural Warranty for normal residential conditions and with proper maintenance, the product will be free of structural defects, and 5 years for commercial use. This structural warranty does not cover surface wear.

5 Year Residential Coating Warranty. The Range is covered by a 5 Year Residential Coating Warranty. We warrant to the original purchaser that the wear layer (Coating Warranty) will not peel or separate from the flooring plank in residential applications for 5 years and 3 years for commercial uses, if it is installed and maintained according the Timber Flooring Installation Guideline and Timber Flooring maintenance & care instructions. Variations in grain, pattern, colour and/or texture are common and are not considered defects. Gloss reduction and scratches are not considered wear through and are therefore not covered by this warranty. Please refer to our Residential maintenance guide for information on how to maintain your floor.

For supply only orders, our hard flooring can be picked up from our Blackburn showroom or from our supplier warehouses. Please contact us to see if we have a warehouse located in your area.

Pick up from the warehouse incurs a $45 handling charge for quantities less than 1 pallet. Pick up from our showroom may incur a handling charge depending on the product ordered.

Delivery can be arranged for most areas in Australia.  Please contact us for a delivery quote.

It is only natural that timber floors will show signs of wear over time. You can expect years of beauty from your floor with regular cleaning and maintenance routines.

Never flood or wet mop the floor as severe damage may occur. Any damage caused by excessive moisture will void the warranty.

Always apply felt pads under any furniture or chair legs to prevent scratches.

Exposure to sunlight's UV rays accelerates oxidation and aging of materials. This may change the colour of the floor. Periodically rearrange the furniture to allow the floor to age evenly.

Never use any of the following products (or similar in nature) on your floor: ammonia-based cleaners, acrylic finishes, wax-based products, bleach, polishes, oil soap, abrasive cleaning soaps, or acidic materials such as vinegar. Many of these products pit
or etch the finish of your flooring or prevent the proper use of recommended maintenance materials.

Damp mop with a pH neutral detergent such as Bona products designed specifically for Timber flooring.